Tribit QuietPlus

Active Noise Cancelling Wireless Headphone Model: BTH100

English User Manual


This manual was converted into an accessible format by A. T. Guys. While we strive to present an accurate version of the manual, errors may occur. Please visit for the latest product information.


Packing List

Wireless Headphones

Carrying Case

USB-C Charging cable

3.5mm Stereo Audio Cable

User Manual

Warranty Card




Wear the headset so that the buttons are on your right ear. You will find 3 buttons in a row on the outside of the headset on the back side. The top button is Volume up, the middle button is Power, and the bottom button is Volume Down. Below this, you will find the Active Noise Cancelation switch. Slide it up toward the buttons to turn it on and down to turn it off. Beyond this is also a 1/8-inch jack for plugging in a wired headphone cable, and a USBC charging port


Turn on/off

Press the center button to turn on/off the device. Press and hold again for 5 seconds to turn off the device


To Connect Via Bluetooth


1.      When the headphones are off, press and hold the power button until the status indicator starts to flash red and blue alternately (the headphones have now entered Bluetooth Pairing Mode). This usually takes a few seconds. If you have not paired a device before, it will go into Bluetooth mode when powered on. The headset will speak “Power on”.

2. Activate the Bluetooth function on your device and wait for it to search for other Bluetooth-enabled devices.

3. Tap the name 'Tribit QuietPlus"on your device once it appears on the list of available devices. The status indicator will flash slowly and the headphones will make a sound when they have successfully paired to your device.


Aux-in Connection


Connect one end of the 3.5mm Stereo Audio Cable to your device, and connect the other end to the 3.5mm Stereo Aux-in Port of the headphones. The Bluetooth headphones will automatically shift from Bluetooth mode into Aux-in mode.


Operation of Buttons


Power Button:


·        Play/Pause: short press

·         Answer/Hang up Calls: short press

·        Next Track: press twice

·        Previous Track: press 3 times

·        Reject Calls: press and hold for 3 seconds

·        Voice Assistant: press for 1 second until tone sounds then release


Volume Buttons

·        Volume Up: short press to increase volume or keep it pressed to continuously increase volume

·        Volume Down: short press to decrease volume or keep it pressed to continuously decrease volume


Connection Conversion between Two Devices


·        Pause the playback of current device

·        Play the audio file of the second device


How to Charge


Connect one end of USB-C charging cable to a 5V power adapter (not included), and the other end into the headphones. The status indicator will glow red during the charging process, then turn blue after the headphones are fully charged (within 3 hours).




Please do the following to reset your headphones if the device isn't working normally:

Connect the headphones to the USB interface of your computer or USB power adapter via the USB-C charging cable. If the status indicator glows red, the headphones have been successfully reset.



FCC Statement


Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limit’s fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user Is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help

This device complies with part IS of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.